Differences

This shows you the differences between two versions of the page.

--- tools:layout:start [2024/06/16 15:50] – [Cell generation] rajit
+++ tools:layout:start [2025/09/21 11:52] (current) – rajit
@@ Line 10: / Line 10: @@
      *  The layout editor is used to complete the layout of the cell.
      *  A new ''.rect'' file is generated from the layout editor that includes all the changes made (metal layers, etc.) when the cell was drawn. A sample script that does this for the magic VLSI layout editor that is part of the layout repository is ''mag2rect.py''.
-   - When ''.rect'' files (that correspond to the finished cells) for a cell is available in the cell rect search path, ACT will read them in instead of generating the unrouted cells. At this step, ACT also generates the LEF for each cell that includes pin information, obstacles, etc. for the rest of the place and route flow.
+   - When ''.rect'' files (that correspond to the finished cells) for a cell is available in the cell rect search path, ACT will read them in instead of generating the unrouted cells.
-==== Headline ====
+ACT also generates the LEF for each cell along with the technology LEF. When the unrouted cells are used, ACT uses dummy pin locations for this purpose. Once the cell is routed (step 2),  the generated LEFs will includes pin information, obstacles, etc. that is suitable for use in the rest of the place and route flow.
+''.rect'' files can be converted to/from magic layer types as well as to/from gds layer types. The details of the ''..rect'' [[.rect|file format]] converts the syntax as well as conversion methods.
-Preliminary layout files for cells required for place and route are generated in the ''.rect'' file format. As the name suggests, this file contains a list of rectangles.
-The purpose of this format is to be layout editor neutral; it is very easy to translate this file into commands to draw the cell in a layout editor.
-An example ''.rect'' file is shown below:
-<code>
-bbox 0 0 24 72
-rect in[0] polysilicon 15 2 16 5
-rect in[0] polysilicon 13 6 15 8
-rect out ndiffusion 19 24 20 27
-rect # polysilicon 13 65 15 67
-rect in[0] polysilicon 13 28 15 35
-outrect out m1 19 24 21 27
-outrect out m1 18 28 21 30
-inrect in[0] m2 11 1 16 2
-inrect in[0] m2 15 2 16 5
-...
-</code>
-The file begins with the bounding box (''bbox'') directive. The four numbers are integer coordinates (in units of the layout scale factor), and the four-tuple corresponds to the lower left x-coordinate, lower left y-coordinate, upper right x-coordinate, and upper right y-coordinate. The rest of the file contains rectangle definitions. An ''inrect'' is a rectangle corresponding to an input pin, and an ''outrect'' corresponds to an output pin, while a ''rect'' is just paint to be drawn. Note that ''inrect'' and ''outrect'' are optional; they could also be simply specified as ''rect'' directives, but are useful as hints in terms of specifying which pins correspond to inputs v/s outputs.
-A rectangle specifier (''rect'', ''inrect'', or ''outrect'') has an optional signal name (''#'' means that there is no label directly attached to the rectangle), followed by the drawing layer name (from ''layout.conf''), and followed by the coordinates for the rectangle. Even if a rectangle does not have a label, it may be electrically connected to another rectangle that has a label. If two rectangles are connected to each other electrically and have different labels, this is reported as an error.
-A rectangle can be followed by an optional string that is ''left'', ''center'', or ''right''. This is simply a hint that says this diffusion region has a transistor to the left only, to the right only, or on both sides. (A cell is drawn with vertical polysilicon.)
-==== Coordinate system ====
-The coordinate system used by rectangles in this file are designed to work directly with ''magic'''s ''box'' command. In the ''magic'' layout editor, a box specified by
-<code>
-:box 0 0 10 20
-</code>
-is of size 10 by 20 units. If we view a box as a collection of 1 by 1 pixels, then this box occupies pixels starting from (0,0) to (9,19). All ''rect''s must be non-overlapping on their respective layers. Note that transistors, diffusion, and poly are all viewed as the same layer.