Differences

This shows you the differences between two versions of the page.

--- tools:layout:start [2024/08/07 10:49] – [Abutment and attributes] rajit
+++ tools:layout:start [2025/09/21 11:52] (current) – rajit
@@ Line 14: / Line 14: @@
 ACT also generates the LEF for each cell along with the technology LEF. When the unrouted cells are used, ACT uses dummy pin locations for this purpose. Once the cell is routed (step 2),  the generated LEFs will includes pin information, obstacles, etc. that is suitable for use in the rest of the place and route flow.
-===== The rect file format =====
+''.rect'' files can be converted to/from magic layer types as well as to/from gds layer types. The details of the ''..rect'' [[.rect|file format]] converts the syntax as well as conversion methods.
-Preliminary layout files for cells required for place and route are generated in the ''.rect'' file format. As the name suggests, this file contains a list of rectangles.  The purpose of this format is to be layout editor neutral; it is very easy to translate this file into commands to draw the cell in a layout editor.
-An example ''.rect'' file is shown below:
-<code>
-bbox 0 0 24 72
-rect in[0] polysilicon 15 2 16 5
-rect in[0] polysilicon 13 6 15 8
-rect out ndiffusion 19 24 20 27
-rect # polysilicon 13 65 15 67
-rect in[0] polysilicon 13 28 15 35
-outrect out m1 19 24 21 27
-outrect out m1 18 28 21 30
-inrect in[0] m2 11 1 16 2
-inrect in[0] m2 15 2 16 5
-...
-</code>
-The file begins with the bounding box (''bbox'') directive. The four numbers are integer coordinates (in units of the layout scale factor), and the four-tuple corresponds to the lower left x-coordinate, lower left y-coordinate, upper right x-coordinate, and upper right y-coordinate. The rest of the file contains rectangle definitions.
-An ''inrect'' is a rectangle corresponding to an input pin, and an ''outrect'' corresponds to an output pin, while a ''rect'' is just paint to be drawn. Note that ''inrect'' and ''outrect'' are optional; they could also be simply specified as ''rect'' directives, but are useful as hints in terms of specifying which pins correspond to inputs v/s outputs.
-A rectangle specifier (''rect'', ''inrect'', or ''outrect'') has an optional signal name (''#'' means that there is no label directly attached to the rectangle), followed by the drawing layer name (from ''layout.conf''), and followed by the coordinates for the rectangle. Even if a rectangle does not have a label, it may be electrically connected to another rectangle that has a label. If two rectangles are connected to each other electrically and have different labels, this is reported as an error.
-A rectangle can be followed by an optional string that is ''left'', ''center'', or ''right''. This is simply a hint that says this diffusion region has a transistor to the left only, to the right only, or on both sides. (A cell is drawn with vertical polysilicon.)
-==== Coordinate system ====
-The coordinate system used by rectangles in this file are designed to work directly with ''magic'''s ''box'' command. In the ''magic'' layout editor, a box specified by
-<code>
-:box 0 0 10 20
-</code>
-is of size 10 by 20 units. If we view a box as a collection of 1 by 1 pixels, then this box occupies pixels starting from (0,0) to (9,19). All ''rect''s must be non-overlapping on their respective layers. Note that transistors, diffusion, and poly are all viewed as the same layer.
-==== Bounding box ====
-This bounding box corresponds to the place and route boundary for the cell. Note that this is for convenience only; this box is automatically re-computed by the ACT layout library based on the geometry of the cell. The ''.rect'' file reader used by the ACT layout flow ignores this line.
-A user-specified place and route boundary and bounding box can be specified using the ''sbox'' directive. This has the same syntax as ''bbox'', except it is used to override the bounding box computation within the ACT library.
-==== Abutment and alignment ====
-The layout library has support for manipulating layout. To aid in this, a ''.rect'' file can include information about how one cell can be abutted with another during procedural layout generation. A special layer name called ''$align'' is reserved for this purpose.
-<code>
-rect # $align 2 2 8 8
-</code>
-This means that the box used for abutting this cell with another has the specified coordinates.
-<code>
-rect $l:name1 $align 2 2 2 2
-</code>
-This means that a left edge alignment marker called ''name1'' is located at the specified coordintes.
-<code>
-rect $r:name2 $align 2 8 2 8
-</code>
-This means that a right edge alignment marker called ''name2'' is located at the specified coordinates.
-Similarly, ''$t:'' and ''$b:'' prefixes are used for top and bottom alignment markers.